- #Epson perfection v500 troubleshooting install
- #Epson perfection v500 troubleshooting drivers
- #Epson perfection v500 troubleshooting software
This seems unusual, since most of the scratches will occur in pictures and not negative, and most objects to be scanned at this time will be photos. The red warning light on the front panel starts flashing, indicating that the scanner is not working. This document contains an overview of the product, specifications, basic and in-depth usage instructions, and information on using options. I think I have an idea what the fault might be: Because I have a second identical scanner (same model number etc) and have tested one against the other. This document contains compliance statements, specifications, and your products limited warranty. It appears that any product which is made from now on will be with this in mind.
#Epson perfection v500 troubleshooting drivers
#Epson perfection v500 troubleshooting software
This software is terrible and likes to reset between each scan. BE SURE TO RE-CHECK YOUR SETTINGS EVERY TIME. The files should be automatically saved to the location you chose. Verify that everything looks OK, then finally hit scan and got eat a few sandwiches, because it can take a loooong time. Note: All your photos will be backwards and upside down because the software expects you to put the film with the emulsion side up. If you don't, then you are scanning with information from the previous scan, which can wreak havoc with lighting adjustments, etc. Make sure you are saving to TIFF format, no compression.Now click the little folder icon in lower right. Save Settings: Yes (you can try, but saving does not work for me).Choose the right ratio for your exposures. Color Control, Continuous auto exposure, Display Gamma 2.2.Either way, it really does make a difference in removing dust and scratches. DIGITAL ICE: Yes, Mode: Quality is very slow, and Speed seems to do pretty much as good of a job.Backlight Correction: It can make a difference, but usually No is the right option.Color Restoration: Yes, but ONLY if you have old-ish photos or negatives.Unsharp Mask: Yes, medium (this one really does make a difference).Fancy buttons directly under the "Adjustments" header: Ignore.6 x 6 equivalencies (I usually go with 3200).35mm equivalencies (fwiw, I use 6400 for good film and 4800 for lesser film):.You can always make it B&W in post-production later) Image Type: 24-bit Color (do color, even if your photo is B&W.Film Type: (Either Positive or Color Negative.On the main window, go through and set the following settings. Open the Epson Scan software and choose "Professional Mode".
The software bombs out if you try to open it when the scanner isn't on. Make sure the scanner is connected to the computer and powered on. Obviously, you need to position the jig so that the toothpicks go in between each exposure. The toothpicks go down, against the film. If it's 35mm film, and you can't get it to lay flat, you may need to lay the cardboard-and-toothpick jig on top of the film (but below the frame) to make sure the film is as flat as possible. I also use a flashlight to shine through the film, so I can see where the edges of the frames are. I use the corner of a microfiber cloth to avoid touching the film with my finger. Using the frame to help hold things in place, very carefully move the film around under the frame until it's positioned such that nothing's going to get cut off. The only way to get those curly pieces of film flat is to pin them between the frame and the glass. The manufacterer wants you to place the film inside the frame, but don't do that. Place the film frame down on top of the negative, placing the tab in the correct slot in the scanner bed. There is one frame for medium format, and another frame for 35mm mounted slides and loose 35mm film strips. However, if you smush the glossy side of the film against the glass, you get newton rings.Ĭhoose the correct film frame for your film size. To get it as flat as possible, you want it smushed against the glass. Why? Because you want the film to be as flat as possible. The emulsion is the matte side of the film. Lay the negative emulsion side down on the glass. You can use puffed air, or soft antistatic brushes as well. I use a clean microfiber cloth to remove large dust particles and hair. Make sure the negatives are as clean as possible, but be extremely careful not to scratch them or get figerprints on them. If there are smudges or marks on the glass, use regular window cleaner, and be sure to dry it 100% Load the Negatives into the Scanner Now you should see glass on the lid as well as the scanner base.Ĭarefully remove all visible dust from the glass with a microfiber cloth. Make sure the reflective mat is removed from the top lid (slide out toward front of scanner).
#Epson perfection v500 troubleshooting install
Download and install the driver and software from here: Preparing the Scanner
0 kommentar(er)
